ログイン
言語:

WEKO3

  • トップ
  • ランキング
To
lat lon distance
To

Field does not validate



インデックスリンク

インデックスツリー

メールアドレスを入力してください。

WEKO

One fine body…

WEKO

One fine body…

アイテム

  1. 116 農学生命科学研究科・農学部
  2. 82 演習林
  3. 演習林報告
  4. 75
  1. 0 資料タイプ別
  2. 30 紀要・部局刊行物
  3. 演習林報告
  4. 75

各種環境条件下における釘接合部及びメタルプレート・コネクター接合部の力学的性質

http://hdl.handle.net/2261/23104
http://hdl.handle.net/2261/23104
2b64865e-f649-45dd-9894-1609489a59c0
名前 / ファイル ライセンス アクション
esrh075012.pdf esrh075012.pdf (1.7 MB)
Item type 紀要論文 / Departmental Bulletin Paper(1)
公開日 2014-09-03
タイトル
タイトル 各種環境条件下における釘接合部及びメタルプレート・コネクター接合部の力学的性質
言語
言語 jpn
資源タイプ
資源 http://purl.org/coar/resource_type/c_6501
タイプ departmental bulletin paper
その他のタイトル
その他のタイトル Mechanical Properties of Nailed Joints and Metal-Plate Connected Joints under Various Environmental Conditions
著者 徳田, 迪夫

× 徳田, 迪夫

WEKO 55555

徳田, 迪夫

Search repository
著者別名
識別子Scheme WEKO
識別子 55556
姓名 TOKUDA, Michio
著者所属
著者所属 東京大学農学部林産学科
著者所属
著者所属 Department of Forest Products, Faculty of Agriculture, University of Tokyo
抄録
内容記述タイプ Abstract
内容記述 含水率変化を受けた釘接合部の引抜き抵抗力及びせん断耐力の変化,それにメタルプレート・コネクター接合部の引張強度の変化を実験によって調べた。釘接合部のせん断試験及びメタルプレート接合部の引張試験では繰返し荷重を加えた。得られた主な結論は次の通りである。(1)釘の引抜き抵抗力は,木材に腐朽が生じない限り,長期的な値は,ほぼ短期の値と同等である。(2)気乾の木材と合板とで構成された釘接合部が乾湿繰返しを何回か経験した後に,両振れ繰返し力を受けた場合,接合部のスリップ量とコントロール試験体のスリップ量の比は1.5~2.0に収束した。神谷の報告によれば,生材と合板で構成された釘接合部の場合には,その比が3以上にも達するので,釘を生材に打つことき避けるべきである。一方,ウェファーボードを側材とした釘接合部では,スリップ量は乾湿繰返しのサイクル数の増加とともに漸増した。このことから,大きな含水率変化を受ける箇所へのウエファーボードの使用は疑問がある。しかし,室内環境条件下で用いる場合には,合板よりもすぐれた面を持ち合わせているので,両者の適切な使い分けが必要であろう。(3)メタルプレート接合部の剛性及び強度を,素材とLVLとで比較すると,破壊のパターンは異なったが,剛性及び強度に関しては,両者の間に有意差はなかった。しかも,LVLは素材に比べると,乾湿繰返しの影響を受けにくい材料であった。従って,実際の住宅で長期使用する場合,LVLのトラス部材としての性能は,素材と同等以上と考えられる。
抄録
内容記述タイプ Abstract
内容記述 Withdrawal resistance of nailed joints and lateral strength of nailed joints subjected to reversed cyclic loading under moisture variable conditions were investigated. And the feasibility of laminated veneer lumber (LVL) for metal-plate connected joints was studied. The following results were obtained. (1) Withdrawal resistance of nailed joints in the long duration was almost the same as that evaluated two days after driving nails as long as the wood was sound. (2) After plywood-sheathed nailed joints were subjected to repetitive moisture cycle, the ratio of the slip to that of control specimens converged to 1.5-2.0 under fully reversed cyclic loading. However, according to Kamiya's report, when driving into wet wood, the ratio was over 3. Nails should be driven into air-dried wood. On the other hand, the joint slip of waferbord-sheathed nailed joints increased gradually as increase of the number of moisture cycle. Waferboard is recommended to be used under the room conditions. (3) In spite of the different failure modes, there wes little difference of stiffness and strength between lumber and LVL metal-plate connected joints as long as the specific gravity or the modulus of elasticity were close. Mechanical properties of LVL joints were affeced less by specific changes of environmental conditions than those of lumber-joints. Since there is wide range of temperature and humidity condition in Japan, this characteristic is advantageous. Therefore, LVL can be used in structural components assembled with metal-plate connectors when economically feasible.
書誌情報 東京大学農学部演習林報告

巻 75, p. 315-350, 発行日 1986
ISSN
収録物識別子タイプ ISSN
収録物識別子 03716007
書誌レコードID
収録物識別子タイプ NCID
収録物識別子 AN00162451
日本十進分類法
主題Scheme NDC
主題 610
出版者
出版者 東京大学大学院農学生命科学研究科附属演習林
出版者別名
The Tokyo University Forests
戻る
0
views
See details
Views

Versions

Ver.1 2021-03-02 03:25:49.105598
Show All versions

Share

Mendeley Twitter Facebook Print Addthis

Cite as

エクスポート

OAI-PMH
  • OAI-PMH JPCOAR 2.0
  • OAI-PMH JPCOAR 1.0
  • OAI-PMH DublinCore
  • OAI-PMH DDI
Other Formats
  • JSON
  • BIBTEX

Confirm


Powered by WEKO3


Powered by WEKO3